Guset User Download PDF. Publications: 93; Followers: 0. GReddy Profec B spec 2 Manual. Created Date: 8/14/ PM. Category: All. 0. Embed. Improper tuning of the Profec B-spec II may cause damage to the engine. GReddy 3 Way Fitting Double Sided Tape Air Filter Instruction Manual. Please make. pdf · Greddy Profec B 3 Knob Boost Controller Installation Instruction Manual, M. pdf · Greddy Profec B Spec Ii 2 Boost Controller Installation Instruction.

Author: Fauktilar Grokinos
Country: Iceland
Language: English (Spanish)
Genre: Art
Published (Last): 27 November 2014
Pages: 191
PDF File Size: 11.30 Mb
ePub File Size: 9.53 Mb
ISBN: 365-1-39977-125-6
Downloads: 87227
Price: Free* [*Free Regsitration Required]
Uploader: Zulugrel

Set the Limiter to turn down the boost when the pressure exceeds the warning point.

Greddy Boost Controller

Show only see all Show only. All listings filter applied. Sorry didn’t realize this thread was soo old, I’m retarded and can’t read dates. I will henceforth refer to what you’re aiming for as “desired boost pressure”. Set GAIN to 0 see above.

Greddy profec-b –

To clear it, go to the peak boost display, and hold down the set knob until the unit beeps and “” is displayed. Boost Solenoid Valve Hose Fittings.

Tune the “Lo” and “Hi” settings corresponding to having the boost maximized during the low gears and during the high gears. To print the manual completely, please, download it. Page 8 Installation Diagram Diagram 1: See each listing for international postage manaul and costs.

Also See for e Instruction manual – 55 pages. Only one thin harness is required to be routed through the firewall. NAME Input name to label each input signal channel. The following steps should be taken in exactly this order, taking into consideration all of the previous information: The kept high boost mode that can be turned on for a set amount of time or on constantly.


An ultra slim controller can display in digital, bar-graph, or graphical modes and can be rotated degree for installation with the included adjustable mount or flush mounted. The maximum boost that you will see is also not consistent throughout the gears, which adds even more to the confusion. Keep in mind that when displaying in kPa, it does not show it technically in kPa, but rather misleadingly in bars, which Greddy inconveniently tries to justify by sticking x kPa next to the display.

Therefore, kPa will be displayed as 1. This page was last updated: Map Select Place check marks on the features you need to program. Record 3 hours of input signals including the e-manage signals can be recorded while in the Display mode.

GReddy Profec B-Spec II Install w/ no instructions – – Mazda RX7 Forum

Manufacturer Part Number If there is no boost falloff, then go to Don’t show me this message again. Includes Controller Vacuum hoses 2 sizes Solenoid val Pressure Sensor Harness Part: This writeup was taken from an evolutionm.

Save manual turbo boost controller to get e-mail alerts and updates on your eBay Feed. UNIT Select the mznual for the selected meter type. Set it to the “safest” of the settings that does not trip your limiter.

P will indicate phase 1 in gredcy upper right corner of the display. Based on the very popular B-Spec.

SET This is how you set the boost pressure. Please enable JavaScript on your browserthen try again. This is where the adjustment starts. Then, secure the Valve assembly to the body using the supplied M6 Bolt and Rubber washer.


GReddy e-01 Instruction Manual

Previous price EUR Also used to setup the optional signal harness and Warning gauges when installed with this unit. Just to add something here If you feel surging and the boost pressure still decreases not sure if this is possible then decrease to the last level that you did not feel surging at. Page 9 Installation Diagram Diagram 2: PEAK is the peak boost value that the unit has seen since the last time it was cleared. Browse Related Browse Related. Psi will also unfortunately be displayed in psi x10 so that 19 psi will show asadding to the confusion.

Use the optional External Input Signal Harness sold separately and select one to grfddy as output signal.

The rpm signal can be inputted by using the optional External Greddu Signal Harness sold separately or through the e-manage unit. Solenoid Valve Harness Type: This page was last updated: Vehicle with factory boost controlling solenoid valve Single port actuator Disconnect the connector and the vacuum lines off from the solenoid valve and plug up the all the vacuum ports.

If you pause the play back and change the Display mode to e-manage Map display screen, the recorded e-manage data can be played back. E – eManage Pressure Link Type: Parts List Pressure sensor Valve unit harness Pressure harness 2. UNIT Select the unit for the input signal.